Making The Miniature Pinscher

Well ….. the wind is howling and the rain is lashing down.  The dogs were all asleep so I started needle felting a Miniature Pinscher.  Not an easy task when it is only going to be small …. 11cms (4 and a half inches) long and the same high.  So I got out the wool and a range of needles – thicker ones for the body felting and finer ones for the legs and face.

min-pin-1

 Usually, I make the body first but as the legs are quite fiddly, I did the front legs first, using fine chenile sticks to felt the wool round, making sure the outsides were black and the inside of the legs red (as observed via Googling lots of Miniature Pinscher pictures!!)

min-pin-2

Once the legs were eventually felted, I made the body from black roving and felted the legs on.  To make sure they are secure, I stitched through them and the body with a long doll needle and black thread, then used black wool to felt over the stitiching.  The body needed quite a lot of felting as the tummy tucks up and the dog actually looks like a wedge shape in real life so I had to slope the back down and the tummy up.  I then felted over the black chest with a band of red brown roving with a fine black line down the centre.  I left the neck mostly unfelted because it needed the head making and attaching.

min-pin-3

min-pin-4

Next for the tail, which was felted around a small piece of a fine chenile stick so that I could bend it appropriately.  The under side of the tail is the red brown, the same  as the inside of the legs and the chest.

min-pin-5

I felted the tail on, making sure it was firmly attached and bent at the right angle.

Next for the head.  I rough felted the shape which was incredibly complicated because the breed has a full face, finer muzzle and eyes that are sort of facing forwards.  I messed and messed with this – starting over at least 3 times!

min-pin-5b

Finally, I added the eyes – small black beads on wire, which are glued into the head after making a hole in the felt with a Bradawl.  I then felted around them with a fine line of cream batting to give the impression of eyelids, which are slanting upwards from the corners.  Next I added the red brown colour to the face and under the chin, glued on the polymer clay nose and felted a fine black mouth line underneath.  I felted a flat piece of black and overlaid it with a fine layer of pink, which I used to cut the ears from, attaching them so they stood high and pointed on the back of the top of the head.  A little more felting and a bit more wool added to give the neck the correct width and strength and he was finally finished.

He took about 5 and a half hours to complete.

min-pin-8

min-pin-7

Prior to making him I made a pretty Chinese Crested, using the same methods as above

_dsc7600

Making The Miniature Pinscher

The Innocent Slumber of the Needle Felted Wire Haired Dachshund

Ah the satisfaction of completing my little replica.  I watched our little mini wire Aldo sleeping and thought – that would be good to needle felt – so my needle came out and I started.

The base was pink – really harsh wool that enabled me to get the shape easily.  I made the legs and head separately and before I attached them I covered his tummy in brown Shetland combed top.   I then dressed the legs with a mix of Icelandic and Shetland top – cut into tiny pieces that I hand mixed to get the wild boar look of the coat.  I left the tops of the legs un-felted so I could attach them to the body and I used a long doll needle to stitch through the front legs so they stayed in the right position whilst I felted them on.  I then attached the head – still in its un-dressed state and looking really odd – the pink made it look like an alien!  It took a while to cover the body in its mixed wool coat and once done I added the tail and started on the head – that was very fiddly – adding eyebrows and a beard, felting on the black nose and doing a fine line for the closed eyelids.

When I was happy that he was in the correct sleeping position and his beard was well needled in, I put him aside and made the basket from Green Perendale batting.  The banket came next, a small piece of doubled Sherpa fleece (that I use for my real dog beds)  I embroidered a small paw print on one corner and overlocked it. 

I finally had my mini miniature – 5 inches long in a basket 6 inches wide!

l1003591

l1003590

l1003589nic

The Innocent Slumber of the Needle Felted Wire Haired Dachshund